We have encountered this post on How to Install a Bathtub directly below on the web and decided it made good sense to share it with you in this article.
Mounting a bath tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately hard task. If the old bathtub is easily available, the project can relocate easily; if you have to open a wall to get rid of the old bathtub and position the brand-new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will require an assistant to leave the old tub and also embeded in the new one. Make sure you have actually qualified yourself for the work as well as fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to think about using one before you begin. Opportunities are you might need a specialist plumber to make tube connections.
This post will aid you install a brand-new bathtub in your washroom if you have currently acquired a new bathtub as well as do not need to transform the arrangement of your previous water system pipes.
Your devices as well as product checklist must consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing substance.
Prior to moving on to fit the brand-new taps, compare the pipe links on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Secure the faucet in position with the maker supplied backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the tub until the level checks out level.
To mount taps, fit the bottom of the outermost versatile tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the supply of water and examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bath tub and also inspect the overflow outlet and the regular electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bathtub has been made use of at least once as this will certainly resolve it into its last placement.
Preparing for the Setup
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall between the bathroom and also the tiling, bring about difficulties with moisture as well as possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can break fairly very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very taken with A Step-by-Step Guide to Installing a Bathtub and I'm hoping you liked my blog posting. Those who liked our post please do not forget to pass it around. Thanks so much for your time spent reading it.
Request An Appointment